LOTOS LT5000D Plasma Cutter, 2024 Upgraded 5/8 inch 16mm Clean Cut 3/4 inch 20mm Severance Cut 50A Plasma Metal Cutter Machine, Plasma Cutting Equipment, Dual Voltage 120V or 240V, Brown

I have included a few pictures of my first cutting project with my new Lotos LTP5000D that I got yesterday evening. I am making a type of hanger that goes outside by the front door. It will be a half circle with a circular image hanging in the middle of it. I had to use a plate from the kitchen to go around with the cutter - it was unbelievably easy! The half circle I had to do by hand - and had to clean it up with the grinder...but I expected that. Next I'll cut out the design that goes in the circular part, and then hang it within the half circle, weld a mounting plate to the half circle, and probably hang it outside. I am using 1/8" flat plate steel.I have a rather large, older plasma cutter I picked up at Harbor Freight many years ago. I tried to use it about 6 months ago and it's not working. I am getting back into metal work in the garage and wanted to get a new, portable plasma cutter. 3 days ago, I went to the 2 big box stores (L. & H.D.) and was disappointed to find that they don't even carry them in the store. I'm glad now that they don't.When I got back home, I went online and started reading info and reviews on diff. machines. Initially I looked at a couple in the $150-180 range on Amazon, but decided to spend more and get a much better one. I didn't know what pilot arc was but I ended up buying the Lotos LTP5000D...and ABSOLUTELY LOVE IT!!My 220 in my garage I and a friend put in many years ago when I got my first plasma cutter. However, the 220 plug on the Lotos is the 3-prong circular pattern plug, which doesn't match my existing outlet. I looked at different ways to make it work, and eventually decided on this: I bought an adapter that has the circular female side and the male side is the two vertical blades (one wider than the other) and the round piece. I also ordered a matching 3-prong outlet, which I wired in place of the existing 220 outlet. It was simple...the two 110 hot wires to the two blades, and the ground (green) to the round one. I did have to go to Lowes this am to get a mounting box to install it. Found one cheap, got it installed, and started cutting metal. Yesterday, I had used the circular plug with the 220 to 110 pigtail and it worked fine...the first time with low amps because I was cutting out the bottom of an old coffee can to make a shroud for a small fan. Problem after that was that I popped the power strip when I was using higher amps and my compressor kicked on. I then plugged the plasma cutter into a different outlet, but twice when the compressor started while cutting, the whole garage power went out. That's when I knew for sure I needed to get my 220 line working, since it's a dedicated line that doesn't affect any other power in the house.Since it's been many many years since I've actually used a plasma cutter, it is taking me a little bit to get back up to speed, but this Lotos unit really makes it easy. And it works so much better on 220! I was nervous that my compressor would have a hard time keeping up, but to my surprise and pleasure, I've found that even running at 42 amps with the psi set around 55-60, when the compressor does kick on, it still is at about 90 in the tank, and only runs for about less than a minute. I'm so glad - don't want to buy a different compressor! Also, that pilot arc is awesome! I can see it really saving me on consumables - with my old plasma cutter, I had to get the torch down to touching the metal, which created a lot of blowback. With this one, I can start the arc much higher and work it in. Also, with the power of this machine, I can start the tip right on the metal and punch through the metal instantly...without the blowback on me or on the torch tip. This will definitely save money by making the tips and the electrodes last longer.So I'd say that after spending $335 on the cutter and about $70 on the pigtail and set of consumables, coming in around $443 for everything, and getting my cutter about 48 hours after ordering it, I am extremely pleased with the purchase. I can't speak for longevity or durability yet, but I can say that the cutter feels solid and well built, and the cords (ground and power/air/arc power combo) seem very durable and capable.For apparent quality, ease of use, and performance, I could easily give this many more stars - if that were possible. I can't say enough about the looks, the feel, and the performance so far with this machine. I've learned the hard way that products can start out amazing and then develop problems, so I can't speak for longevity as yet. But in the short (1 day) time I've been using it, I am extremely satisfied with my purchase, and would highly recommend the Lotos LTP5000D to anyone just starting plasma cutting, needing to switch/upgrade from a current machine, or simply needing a second plasma cutter around the shop or in the truck (this thing is LIGHT - compared to my MIG welder, and especially compared to my stick welder!!!oh...and I can't speak for customer service since I haven't had to contact them - and hope I never do.Get this plasma cutter!!! If it runs as good and easily as mine has so far, you won't regret it!!

This plasma unit (my first) is extremely light and believe it or not, it "looks and feel" well made.It does NOT have the usual made-in-china crappy feel.For comparison my welder is a Miller Multimatic costing several times the cost of this plasma cutter.Obviously this plasma unit is no Miller but so far it can hold its own for metal cutting.The controls are easy to use including a digital display for the amp setting.The torch has a safety cover over the trigger. All the hoses and wires are covered by a rubberized plastic shield.When comparing these low cost plasma cutters, here're some Pluses of this unit:- NO contact with the material (using the included non-wire metal piece): This prolongs life of consumables, provides cleaner cuts, and is easier to use. Usually found on higher price units.- It works well under both 110/220 voltage - but you need a pigtail adapter to use it in 115.- Obviously it can cut much deeper under 220v ( up to 3/4 ragged 1/2 pretty clean) but at the right depth (¼ or less) it cuts just fine at 115v. Some people report cutting at ½ in 115v. I haven't.- As I said above to use it with 110 make sure to get / buy the pigtail adapter- It has a built-in air regulator with a water cup filter (insures your air is dry and clean): Comes included as a standard feature. Something that some $2000 plasma cutters lack.- It also has built-in male adapter for you to plug in your air hose from compressor. Notice you MUST have an air compressor to provide the air that will be turned to plasma.I've used it several times times and have loved it so far.At first I used at 115 but now I use it at 220.The consumables are available here in Amazon and in their own website (uwelding don't com)Cutting straight lines and circles require a steady hand.But most people use templates, straight edges or compass-like tools. They do make a compass-tool for this unit at their website uwelding.com. It allowed me cut circles of different radii up to 18 inches (for 36" diameter circles):I wish more people made templates for this plasma unit.I'm posting some pictures. Will post some videos.PS: I highly recommending getting a plasma water table to catch all the by products (slag) from the molten metal.Amazon sells one I love from 911motorcrossing.I've only owned it for a a few months. And after hearing all the horror stories I sort of expect it to die soon but it keeps on working.